Limited One-Year Warranty. Previous Page. Next Page. Pro th series non-programmable digital thermostat 36 pages. Honeywell programmable thermostat installation guide 20 pages.
The Magic Stat name is synonymous with innovation and state-of -the-arl electronic controls. Your new thermostat will automatically control the temperature in your home, keeping you comfortable while saving energy when programmed according to the instructions in this manual. HOLD—allows you to set and hold one temperature until you choose to change it. This feature can be used only after the thermostat has been programmed.
See page Page 4: Programming Your Thermostat If you are programming the thermostat before installation, be sure the battery is installed see page 4. During programming, if you leave the thermostat for a few minutes, it will go blank to save battery power.
This does not affect your program; hold HEAT key to relight the display. Youcan backup bytapping thekey. The normal room temperature display will return. The fan goes on Auto On m—l and off with the air conditioner in summer. In winter, the fan on most systems starts a few minutes after the furnace comes on. Repeat steps on pages until all changes you want are made. Mode Tap or hold until temperature indicators show the range at which you want the thermostat to maintain the heating and Heat cool cooling temperatures.
For best results, replace battery every 5 years. To replace: Open right-hand thermostat door. After each turn, allow the thermostat to stabilize about 30 seconds. Continue this procedure until the thermostat has the same temperature reading as the room thermometer. Your furnace is interrupting power to the thermostat. This is not a problem, as the 9 V alkaline battery will be adequate to carry the program for the entire heating season.
Do NOT use a rechargeable battery. Oeacription Parl No. This warranty shall not apply if it is shown by Honeywell that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer. Print page 1 Print document 15 pages. Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals? Sign In OR. Don't have an account? Complain wrong Brand wrong Model non readable.
Prepare for installation a. Carefully unpack your new thermostat. Save your receipt and make sure you have the following p Gather the needed tools and supplies listed below. Make sure that your heating and cooling systems are working properly. If there is a problem wi Step 2. Remove the old thermostat Step 3. Install the mounting plate Step 4. Step 5. Wire the thermostat terminals Step 6. Mount the thermostat Step 7.
Install the batteries Special wiring instructions A clock thermostat with C or C1 terminals A clock thermostat has one or two extra wires attached to the C or C1 terminals that allow the cl Locate the wires that are connected to the clock terminals marked C or C1. As you disconnect the wires, do not allow these wires to touch.
Wrap the wires separately, using electrical tape to insulate the wires. Place the wires where they will not interfere with the operation of the new thermostat. You wi Continue with the installation as instructed on page 4 at step 2e.
Six or more wires If your old thermostat has six or more wires excluding clock wires attached to the C or C1 termi Three thermostat wires If you have three wires for heating only and can operate the fan using the fan ON switch, the Wires that are not connected to the old thermostat If there are extra wires that do not connect to your old thermostat, do not label them. You will Five wires connected to the old thermostat Your new thermostat has a factory-installed metal jumper between the R and Rc terminals Fig.
Old thermostat terminals that do not match new thermostat terminals Use the table below to wire the new thermostat. Step 1. Set the current time and day Step 2. Learn about the programming features Programming tips Step 3. Program the heating schedule a. Write in the times and temperatures that you want to program for your heating schedule. Step 4. Program the cooling schedule a.
Write in the times and temperatures that you want to program for your cooling schedule. Repeat steps 3c. Press once. The time is displayed. Press and hold or until the correct time is displayed.
The current time and day and the current temperature are displayed. Set the Fan and System switches Replace the batteries a. Make sure that the System switch is set in the OFF position.
Open the battery door. Press on the left side of the batteries to remove them. Install the new batteries. Make sure that the positive and negative terminals are oriented cor Override the program settings Frequently asked questions Customer assistance For all questions concerning this thermostat, please read and follow the instructions. If you nee Recycling Thermostat a. Remove the cover of your old thermostat Fig.
Inspect the old thermostat wiring. If the wiring meets any of the following conditions, see th Using the enclosed labels, mark the wires with the letter of the terminal that it is attached Disconnect the wires from the old thermostat and wrap the wires around a pencil to keep them f Separate the mounting plate from the thermostat using a coin, as shown in Fig 5.
Position the mounting plate on the wall. Be sure the mounting plate sits flush against the wal
0コメント